Pentair Variable Speed Pump User Manual
- Pentair Variable Speed Pump IntelliFlo Manuals & User Guides. User Manuals, Guides and Specifications for your Pentair Variable Speed Pump IntelliFlo Swimming Pool Pump. Database contains 1 Pentair Variable Speed Pump IntelliFlo Manuals (available for free online viewing or downloading in PDF): Installation and user manual.
- INTELLIFLO® 2 VST Variable Speed Pump Installation and User’s Guide i P/N 356876 Rev. A 9/14/15 If you have questions about ordering Pentair Aquatic Systems replacement parts.
- Aug 22, 2016 BEST ANSWER: My understanding is that variable speed pumps offer better energy efficiency than fixes speed pumps with flow control valves. Imagine a 'fixed speed car'. Accelerator fixed to the floor (max), and you use the brakes to control the speed:-) A variable speed pump is like a sensible car. It allows you to slow down by letting off the gas.
- Intelliflo Variable Speed Pump Owners Manual
- Pentair Variable Speed Pool Pump Owners Manual
- Pentair Variable Speed Pump Manual
The Pentair SuperFlo VS is an energy efficient, variable speed pool pump ideal for standard swimming pools requiring up to 1-1/2HP pool pump. The SuperFlo VS is the only variable speed pump on the market today with 115/208-230V and 50/60 Hz single phase capability.
Intelliflo Variable Speed Pump Owners Manual
49
IntelliFlo Installation and User’s Guide
Alerts and Warnings
The IntelliFlo displays all alarms and warnings on the control panel display. When an alarm or warning
condition exists, the corresponding LED will be lit on the display. All control panel buttons are disabled until
the alarm or warning is acknowledged with the Enter button. Press the Reset button to
clear the alarm once the fault condition has been resolved. Note: The IntelliFlo pump will
not start if the impeller is rotating. The alerts and warnings are:
•
Power out failure:
The incoming supply voltage is less than 170 VAC. The drive
faults to protect itself from over current. The drive contains capacitors that keep
it powered up long enough to save the current run parameters. If power is
restored during this process, approximately 20 seconds, the drive will not restart
until completed.
•
Priming error:
The incoming supply voltage is less than 170 VAC. The drive
faults to protect itself from over current. The drive contains capacitors that keep
it powered up long enough to save the current run parameters. If power is
restored during this process, approximately 20 seconds, the drive will not restart
until completed.
•
Overheat alert:
If the drive temperature gets above 130 degrees, the IntelliFlo
will slowly reduce speed until the over temperature condition clears.
•
Anti-freezing:
When active, the motor will run at 1000 rpm for 60 minutes. Only active in Filter and
Manual modes. Note: The IntelliFlo's internal anti-freeze protection is disabled when connected to
an IntelliTouch system. Freeze protection is provided by selecting YES at the ON WITH FREEZE
portion of the IntelliTouch's appropriate circuit function menu. To re-enable the IntelliFlo's internal
anti-freeze protection, the power to the drive must be cycled off then back on.
•
Blocked system:
Detects a blocked suction line. This alarm resets automatically after 30 seconds
and the pump restarts.
•
System service soon:
Alerts the operator that the pump discharge pressure has reached the Clean
Filter Pressure as setup in the Filter Menu. The filter status will be displayed as 100%. The yellow
warning LED will be on until a backwash cycle is operated. The IntelliFlo will automatically reduce
speed as necessary to not exceed the Clean Filter Pressure.
•
Over current:
Indicated that the drive is overloaded or the motor has an electrical problem. The
drive will restart 20 seconds after the over current condition clears.
•
Over voltage:
Indicates excessive supply voltage or an external water source is causing the pump
and motor to rotate thereby generating an excessive voltage on the drives internal DC bus. The
drive will restart 20 seconds after the over voltage condition clears.
Suction Blockage
When something blocks the suction or the pump fully it will shut off immediately (within 1 second). It will
also shut off after a few seconds of dead heading with the same alert. The unit will come back on in 30
seconds and ramp up slowly. This function should be tested with all new installations by directing the flow to
one suction and covering it with a piece of material other than someone’s hand. This alert is deactivated in
Manual mode.
Section 6
Troubleshooting
IMPORTANT: Before troubleshooting the IntelliFlo pump, read and follow all warning notices,
instructions and safety precautions on pages iii and vi.
Filter
Vacuum
Back
Wash
Manual
Enter
Pentair Variable Speed Pool Pump Owners Manual
Select
Start
Stop
Reset
Feature
2
Feature
1
Men
u
Escape
On
Warn.
Alarm
IntelliFlo
®
Syst
System
emBlock
Block
ALARM!
ALARM!
1
IntelliFlo VS-3050 Installation and User’s Guide
Section 1
Overview
IntelliFlo
®
VS-3050 Variable Speed PumpKenwood user manual download.
The IntelliFlo VS-3050 variable speed pump is well suited for all of your pool, spa, cleaner, waterfall and
other water application. Using the control panel, IntelliFlo can use one of the four selectable preset speeds
or the pump speed can be adjusted to run at a specific speed. IntelliFlo outperforms all conventional pumps
in its class. Advanced energy conservation features ensure that your filtration system is operating at peak
efficiency.
IntelliFlo VS-3050 models
Pentair Variable Speed Pump Manual
The IntelliFlo VS-3050 operates at a maximum system flow of 160 gallons per minute (GPM)
The IntelliFlo VS-3050 can operate from 400 RPM to 3450 RPM with preset speeds of 750, 1500, 2350,
and 3110 RPM. The pump can be adjusted from the control panel to run at any speed between 400 RPM
to 3450 RPM for different applications. The IntelliFlo pump control panel alarm LED warns the user
against under and over voltage, high temperature, over current and freeze protection. See page 29 for the
LED alarm and warning sequence codes.
External Control
The IntelliFlo VS-3050 can communicate with an EasyTouch, IntelliTouch or SunTouch control system or
the IntelliComm communication center via a two-wire RS-485 connection for remote speed control. The
RS-485 communication cable is included with each pump. The EasyTouch and IntelliComm provide the
ability to remotely control the IntelliFlo with four preset speeds. The IntelliTouch can be configured to use
eight speeds with the IntelliFlo VS-3050.
IntelliFlo VS-3050 variable speed pump